Technical Statement
Product Description
ARDEX WPM 1000 Weldable Waterproofing Membrane is a versatile rubber membrane that can be heat welded. It is suitable for waterproofing underground tanking, roofs, decks and tiles. ARDEX WPM 1000 is made up of synthetic rubber with properties which resist ageing from heat, sunlight and ozone and is heat weldable. Polypropylene filaments are welded onto both sides of the membrane for better wetting by water based adhesives. It has excellent gas impermeability and toughness and remains flexible at low temperatures.Laps and corners are to be heat formed and/or welded. Tiling can be done directly on the membrane after 60 minutes with common ARDEX tiling adhesives like X 77, X 56 STS 8/E 90, Quickbond/Abalastic, 2 part Optima or ABAFLEX.
Scope of use
ARDEX WPM 1000 is suitable for waterproofing underground tanking, rooftops, decks, undertile, canal and pond linings.
ARDEX WPM 1000 can be applied to fibre cement compressed sheet, closed cell polyurethane foam, plywood, timber, new or old concrete, wet wall linings i.e. Gib, Aqualine, VillaBoard.
ARDEX WPM 1000 is not suitable as a trafficable surface. ARDEX WPM 1000 is compatible with undertile heating systems. For electric undertile heating, the wire must be covered with a thin screed prior to laying the membrane.
New Zealand Building Code (NZBC)
The product will, if employed in accordance with the supplier's installation and maintenance requirements, assist with meeting the following provisions of the building code:
- Clause B2 Durability: Performance B2.3.1(b)
- Clause E2 External moisture: Performance E2.3.1, E2.3.2
- Clause E3 Internal moisture: Performance E3.3.6
- Clause F2 Hazardous building materials: Performance F2.3.1
Supporting evidence
The product has and can make available the following additional evidence to support the above statements:
Product Criteria
Design requirements
ARDEX WPM 1000 Weldable Waterproofing Membrane is a versatile rubber membrane that can be heat welded. It is suitable for waterproofing underground tanking, rooftops, decks, undertile, canal and pond linings.
ARDEX WPM 1000 is made up of synthetic rubber with properties which resist ageing from heat, sunlight and ozone and is heat weldable. Polypropylene filaments are welded onto both sides of the membrane for better wetting by water based adhesives. It has excellent gas impermeability and toughness and remains flexible at low temperatures.
Laps and corners are to be heat formed and/ or welded. Tiling can be done directly on the membrane after 60 minutes with common ARDEX tiling adhesives like X77, X56 STS8/ E90, Quickbond/Abalastic, 2 part Optima or ABAFLEX.
Installation requirements
Substrates must be dry, clean and stable, with surfaces that are even and free from nibs, sharp edges, dust, dirt or other materials such as oil, grease etc.
For further details of substrate preparation, please refer to the ARDEX WPM 1000 Datasheet, or contact ARDEX Technical Support on 0800 227 339.
Roll out ARDEX WPM 1000 and cut to the measured length. Smooth ARDEX WPM 1000 on contact to minimise air entrapment beneath the membrane. Floor sheets of ARDEX WPM 1000 must extend up the wall at least 150mm. Make sure the ARDEX WPM 1000 is laid tightly into all corners. Wall sheets of ARDEX WPM 1000 should overlap the 150mm upstand. Weld seams and laps with the Leister Triac S Hot Air Gun. Roll with a rubber roller to ensure seams and laps are secure.
Apply the ARDEX WPM 1000 membrane 1800mm up the walls or to a height of 150mm above the shower rose. For unenclosed showers the membrane must extend a minimum of 1500mm out from the shower rose.
Maintenance requirements
No maintenance of the membranes will be required provided significant substrate movement does not occur and the tile finish remains intact. Regular checks must be made of the tiled areas to ensure they are sound and will not allow moisture to penetrate. Any cracks or damage must be repaired immediately by repairing the tiles, grouts and sealants.
In the event of damage to the membrane, the tiling must be removed and the membrane repaired by removing the damaged portion and applying a patch as for new work.
Drainage outlets must be maintained to operate effectively, and ceramic or stone tile finishes must be kept clean.
Quality Assurance
 |
ISO 9001 (Quality Management) |
Relationships
 |
Member of New Zealand Green Building Council |
 |
New Zealand Made |
