Technical Statement
Product Description
Vulcan Cladding is created from thermally modified New Zealand plantation
timber for superior beauty, durability and weathering characteristics.
Horizontal timber weatherboards have been well proven
since colonial times to perform in New Zealand’s harsh conditions.
Abodo’s WB10
profile offers a new take on the traditional rusticated profile that allows for
horizontal secret fixing, offering a clean aesthetic to the building façade.
A
traditional bevel back profile is also available with classic and strong shadow
lines.
Scope of use
Vulcan Cladding Systems are exterior wall claddings and soffit on a drained cavity suitable for buildings:
⦁ timber framed to NZS3604:2011 Timber framed buildings or steel framed to NASH Standard Part 2: May 2019 Light Steel Framed Buildings
⦁ located in a wind zone up to and including Extra High wind zone (as specified in NZS3604)
⦁ within the scope of Acceptable Solution E2/AS1 para 1.1, and with risk score not greater than 20
⦁ located no closer than 1m from a relevant boundary
⦁ in any exposure zone (excluding microclimates) (as specified in NZS3604)
New Zealand Building Code (NZBC)
The product will, if employed in accordance with the supplier's installation and maintenance requirements, assist with meeting the following provisions of the building code:
- Clause B1 Structure: Performance B1.3.1, B1.3.2, B1.3.3, B1.3.3(a), B1.3.3(f), B1.3.3(h), B1.3.3(j), B1.3.4
B1 Structure: By comparison with weatherboard profiles specified in Acceptable Solution E2/AS1
Abodo Weatherboard Codemark Certificate
- Clause B2 Durability: Performance B2.3.1(b)
B2 Durability: By assessment against the provisions of Acceptable Solutions B2/AS1 and E2/AS1, and testing and expert opinion with the provisions of Verification Method B2/VM1.
Abodo Weatherboard Codemark Certificate
- Clause E2 External moisture: Performance E2.3.2, E2.3.5, E2.3.7
E2 External moisture: By comparison with the provisions of Acceptable Solution E2/AS1.
Abodo Weatherboard Codemark Certificate
- Clause F2 Hazardous building materials: Performance F2.3.1
F2 Hazardous building materials: By comparison with accepted chemical preservative treatments specified by Acceptable Solution B2/AS1.
Abodo Weatherboard Codemark Certificate
Evidence
The product meets the requirements set out in the following documents, or relevant parts of cited standards within the documents:
Abodo Cladding meets the requirements set out in the following documents, or relevant parts of cited standards within the documents:Abodo Cladding was tested in accordance with, and meets the requirements of E2/VM1.
Supporting evidence
The product has and can make available the following additional evidence to support the above statements:
Use in Service History
Abodo Vulcan weatherboards have been in service since 2011 in NZ with thousands of houses and buildings using Abodo Vlucan in NZ and around the world
Product Criteria
Design requirements
The Abodo
Codemark Weatherboard system has a range of profiles, exterior mouldings and
accessories. Abodo has it’s tested Protector Waterborne stain colour range, along
with 2 reactive coatings and can offer factory coated solutions.
It is
designed for use as a cladding for residential and small commercial buildings.
It is suitable for buildings within the scope
of E2/VM1 and with a 'Risk Score' of 20 or below per the Weather Tightness Risk
Matrix outlined in E2/AS1.
It is suitable for buildings
in wind zones up to and including Extra High as defined in NZS 3604. Buildings
in wind zones Extra High and above require a rigid underlay, longer fixings and
larger flashings.
Abodo Cladding- Horizontal
is to be installed on either a 20mm cavity batten or 45mm structurally fixed cavity
batten. Weatherboards are fixed at max 600mm centres and can be secret fixed or
face fixed.
Secret fixing: use
flat head ring shank nails or self drilling, self counter sinking head screws
so as to achieve 30mm penetration into structure and positioned 12mm from the
tongue edge. Screw fixing is recommended.
Face fixing: use rose or pentagon head annular groove nails
(hand driven) to achieve minimum 30mm penetration into structure and positioned
approximately 10mm beyond the over- lap. Note: Silicone bronze/copper fixings
can be subject to oxidation during weathering, resulting in discolouration and
weeping around fixing head.
Installation requirements
Abodo Cladding - Horizontal is to be installed in accordance with the Abodo Codemark Weatherboard Cladding Manual and details drawings. Please refer to Abodo website for all installation instructions and detail drawings.
Maintenance requirements
Maintenance is to be in accordance with the maintenance guidelines available on Abodo's website. Wash down every 12 months with gentle detergent, warm water and soft brush. If possible it is recommended to apply a further coat of oil after approx 12 months of weathering. Make a maintenance check every two summers. Check all weatherboards, junctions, flashings, mouldings and replace or remediate as required to maintain weather tightness of the cladding system. For heavily soiled or mouldy areas use Rejuvenator or similar timber cleaner, apply active mouldicide and recoat with penetrating oil. Re-coat every 2-4 years or as required to maintain colour and integrity of coating. Re-coat period may be longer or shorter depending on climatic conditions and/or positioning of cladding to the sun. Preparation with Rejuvenator or other similar oxalic timber cleaner is recommended prior to coating. For Sioo:x coated timber refer to specific maintenance information.
Warrantees
Abodo timber carries a 15 year warranty.
https://www.abodo.co.nz/resource/Built-to-Last-Warranty-15yrs-Vulcan-Abodo-Wood.pdf
Environmental
Abodo timber is thermally modfied, NZ Radiata Pine. There are no chemicals used for this process.
Abodo timber can contribute points to Homestar/Greenstar and is considered Red List Free via these certifications:
Abodo EPD
FSC Certificate
Abodo Declare Certificate
Relationships
 |
Member of New Zealand Green Building Council |
 |
New Zealand Made |
Building Product Information Requirements
Manufacturer
Legal Trading Name:
Abodo Wood Limited
Business Email:
info@abodo.co.nz
Contact Number/s:
9 2490100
Product Identifier
VULCAN CLADDING WB10 138X20, VULCAN CLADDING WB10 180X20, VULCAN NEXUS WB10 180X20, VULCAN CHARRED
Warnings
This product has no warnings associated with it.
