PD3™ Dowel Cradle with RynoBar™

The patented PD3™ design features a tapered and sleeveless plate dowel that provides the world’s best performance in limiting joint deflection to provide superior joint stability.

The PD3™ Dowel Cradle provides the highest deflection control tolerance in line with ACI Standards recommendations to limit joint spalling, facilitates load transfer and provides the lowest risk of restraint that ensures the best serviceability outcome for the slab design. The use of the PD3™ system extends the life-cycle of the floor to provide the highest level of floor efficiency for tenants and the highest return on investment for the asset owner.

PD3™ Dowel Cradles are designed to provide a total contraction joint system solution by incorporating two systems in the one solution. The tapered PD3™ plate dowels allow for lateral movement eliminating the need for a plastic dowel sleeve. The wire cage (cradle) acts as a chair and spacer to ensure the dowels are aligned and maintained at the correct height and spacing during the pouring of the slab.

The elimination of the plastic sleeve from the dowel ensures direct concrete to steel contact , providing the best possible control of load deflection by eliminating the crush factor of the plastic, and in turn, tighter control tolerance than other sleeved plate dowel systems.

PD3™ Dowel Cradle - Now with RynoBar™  

The RynoBar™ is a patented plastic Travel Bar, or sacrificial retention system pre-fitted to all Danley™ PD3™ Plate Dowel Cradles. Traditionally, a series of deformed steel bars are tack-welded to keep cradles intact whilst in transit to site.  Leading engineers and contractors suspect that un-cut steel travel bars are the significant factor in flooring failure resulting from restraint (parallel cracking).

The RynoBar™ is designed to perform 2 pivotal tasks:

(1) As a travel bar, the RynoBar™ is tough when it needs to be - ensuring that PD3™ cradles are intact during transit and installation on site.

(2) The RynoBar™ features an innovate rib-design that yields at <1kN in early concrete shrinkage, which do not need to be cut before the placement of concrete. RynoBar™ saves time and effort on site.

Features:

• The PD3™ Dowel Cradle features a plate dowel with bond breaker allowing concrete to steel contact.
• The PD3™ Dowel Cradle utilises a tapered plate dowel that allows lateral movement without the use of a plastic sleeve.
• The wire cradle construction ensures the accurate placement and alignment of the plate dowels at the correct centres and height within the slab.
• Available in 6mm, 10mm and 20mm plate dowel thicknesses. Cradles are supplied in 3 metre standard lengths.
• PD3™ 20mm is available on a made-to-order basis.

Advantages:

• No plastic sleeves required.
• Direct steel contact allows superior load deflection control.
• Engineered to meet Super Flat Floor (SFF) requirements, ACI 360-R10.
• The use of the PD3™ Dowel Cradle creates a lateral and longitudinal movement void.
• Reduces the risk of restraint.
• Provides fast and accurate horizontal and vertical placement.
• Superior control of vertical deflection increases the life span of gap sealants both internally and externally.
• Prolonging the life of gap sealants also protects against moisture and debris migrating into joint cavity.
• Wider sweet spot for sawcut provides greater tolerance for contractor accuracy.
   

The Benefits & Advantages of RynoBar™

• Improved Safety: Eliminates the sharp edges on traditional steel travel bars.
• Faster Set up & Installation: Saves time and money! Say goodbye to cutting traditional steel travel bars.
• Quality Assurance: RynoBar™ is engineered to accurately yield at the saw cut joint.
• Durability: Designed tough when it needs to be! RynoBar™ will get your PD3™ cradles on site in one piece.
• Quality Design: The RynoBar™ is proudly designed and manufactured in Australia!